路由器上电和重新启动的过程中，在配置终端的屏幕上首先将显示：
****************************************************************************
* *
* H3C MSR930 BootWare, Version 5.02 *
* *
****************************************************************************
Copyright (c) 2004-2014 Hangzhou H3C Technologies Co., Ltd.
Compiled Date : Dec 8 2014
CPU Type : P1010
CPU L1 Cache : 32KB
CPU L2 Cache : 256KB
CPU Clock Speed : 533MHz
Memory Type : DDR3 SDRAM
Memory Size : 256MB
Memory Speed : 667MHz
BootWare Size : 1024KB
Flash Size : 128MB
CPLD Version : 1.0
PCB Version : 3.0
BootWare Validating...
Press Ctrl+B to enter extended boot menu... //当系统出现“Press Ctrl+B to enter extended boot menu...”时，马上按下
BootWare password: Not required. Please press Enter to continue. //按Enter键系统进入BootWare主菜单
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================
|<1> Boot System
|<2> Enter Serial SubMenu
|<3> Enter Ethernet SubMenu
|<4> File Control
|<5> Restore to Factory Default Configuration
|<6> Skip Current System Configuration
|<7> BootWare Operation Menu
|<8> Clear Super Password
|<9> Storage Device Operation
|<0> Reboot
============================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3 //在BootWare菜单下键入<3>，可以进入以太网口子菜单
==========================
|Note:the operating device is flash
|<1> Download Application Program To SDRAM And Run
|<2> Update Main Application File
|<3> Update Backup Application File
|<4> Update Secure Application File
|<5> Modify Ethernet Parameter
|<0> Exit To Main Menu
|
============================================
Enter your choice(0-5): 5 //键入<5>，修改以太网口参数
==========================
|Note: '.' = Clear field.
| '-' = Go to previous field.
| Ctrl+D = Quit.
============================================
Protocol (FTP or TFTP) :ftp tftp //选择传输协议，根据实际情况选择，本案例使用tftp协议进行传输
Load File Name :zpceshi.bin
:MSR800-CMW520-R2516P24.BIN //下载文件名，要与下载的实际文件名一致
Target File Name :zpceshi.bin
:MSR800-CMW520-R2516P24.BIN //存储的目标文件名。缺省情况下与服务器端文件名一致
Server IP Address :192.168.1.1 192.168.1.10 //TFTP/FTP服务器的IP地址
Local IP Address :192.168.1.2 192.168.1.1 //本地IP地址，为TFTP/FTP客户端设置的IP地址
Gateway IP Address :0.0.0.0 //网关IP地址。当与服务器不在同一网段时需要配置网关地址，否则直接键入
==========================
|Note:the operating device is flash
|<1> Download Application Program To SDRAM And Run
|<2> Update Main Application File
|<3> Update Backup Application File
|<4> Update Secure Application File
|<5> Modify Ethernet Parameter
|<0> Exit To Main Menu
|
============================================================================
Enter your choice(0-5): 2 //键入<2>为升级主启动文件
Loading.....................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
......................................Done!
32570368 bytes downloaded!
Updating File flash:/MSR93X-CMW520-R2514P14.BIN.............................
............................................................................
............................................................................
......................................................................Done!
==========================
|Note:the operating device is flash
|<1> Download Application Program To SDRAM And Run
|<2> Update Main Application File
|<3> Update Backup Application File
|<4> Update Secure Application File
|<5> Modify Ethernet Parameter
|<0> Exit To Main Menu
|
============================================================================
Enter your choice(0-5): 0 //选择<0>，返回BootWare主菜单
===========================
|<1> Boot System
|<2> Enter Serial SubMenu
|<3> Enter Ethernet SubMenu
|<4> File Control
|<5> Restore to Factory Default Configuration
|<6> Skip Current System Configuration
|<7> BootWare Operation Menu
|<8> Clear Super Password
|<9> Storage Device Operation
|<0> Reboot
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 1 //选择<1>，启动系统即可完成版本升级